INSTRUCTION BOOKLET
Fully Automatic Burr Grind & Brew™ Thermal Coffeemaker
DGB-900 Series
For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
WARNING: RISK OF FIRE
OR ELECTRIC SHOCK
NOTICE
This appliance has a polarized plug (one blade
is wider than the other). To reduce the risk of
electric shock, this plug will fit into a polarized
outlet only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician.
The lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of fire or electric
shock to persons.
Do not modify the plug in any way.
OPERATING NOTICE
Clogging and backing up of water and/or
coffee in the filter basket can occur under
any or a combination of any of the following
conditions: The use of too finely ground coffee,
using two or more paper filters, using the gold
tone filter in conjunction with a paper filter or
not properly cleaning coffee grounds from the
gold tone filter, or allowing coffee grounds to
spill over the filter.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
Caution: Never open the filter basket during
the brewing cycle, even if no water is draining
from the filter basket, since extremely hot
water/coffee can spill out from the filter basket
and cause injury. If water/coffee is not draining
from the filter basket during the brewing cycle,
unplug the unit and wait 10 minutes before
opening and checking the filter basket.
SPECIAL CORD SET
INSTRUCTIONS
A short power-supply cord is provided to
reduce the risks resulting from becoming
entangled in or tripping over a longer cord.
Longer extension cords are available and
may be used if care is exercised in their use.
If a long extension cord is used, the marked
electrical rating of the extension cord must be
at least as great as the electrical rating of the
appliance, and the longer cord should be
arranged so that it will not drape over the
countertop or tabletop where it can be pulled
on by children or tripped over.
WARNING
rISK oF FIre or eLeCTrIC SHoCK
do noT open
WArnInG: To reduCe THe rISK oF FIre or eLeCTrIC SHoCK,
do noT remoVe CoVer (or BACK)
no uSer-SerVICeABLe pArTS InSIde
repAIr SHouLd Be done BY AuTHorIZed SerVICe perSonneL onLY
ꢁ
INTRODUCTION
IMPORTANT UNPACKING
The burr mill grinder in your new Fully Automatic INSTRUCTIONS
Burr Grind & Brew™ Thermal Coffeemaker is
1. Place the box on a large, sturdy, flat
responsible for the superior coffee flavor you are
about to experience! Add to that the pleasure of
choosing the flavor strength you like best, easy-
to-use controls, and a thermal carafe that keeps
coffee hot and fresh for hours, and you’ll
understand why we say this Cuisinart®
coffeemaker
surface.
2. Remove the instruction book and any other
literature.
3. Turn the box so that the back side of the
coffeemaker is down and slide the
coffeemaker from the box.
is a grind above the rest. Enjoy!
4. After the coffeemaker has been removed,
place the box out of the way and lift off the
left and right polyfoam insert.
CONTENTS
5. Remove cardboard insert from carafe
handle.
Important Safeguards. . . . . . . . . . . . . . . . . . . .2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Unpacking Instructions . . . . . . . . . . . . . . . . . .4
The Quest for the Perfect Cup of Coffee. . . . .5
Features and Benefits . . . . . . . . . . . . . . . . . . .6
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . .8
Programming Your Coffeemaker . . . . . . . . . . .8
Inserting the Water Filter . . . . . . . . . . . . . . . . .9
Making Coffee with Whole Beans . . . . . . . . . .9
Making Coffee with Pre-Ground Beans. . . . .11
Cleaning and Maintenance . . . . . . . . . . . . . .11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .12
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
6. Remove the cardboard insert between the
carafe lid and Brew Pause™ mechanism by
sliding it out of the unit.
7. Grasp the carafe by its handle, remove it
from the resting plate, and remove the
polybag.
8. Remove the polybag covering the
coffeemaker.
We suggest you save all packing materials in
the event that future shipping of the machine
is needed. Keep all plastic bags away from
children.
ꢂ
Element 3: Grind
THE QUEST FOR THE
The grind is critical for proper flavor extraction. If
the grind is too fine, over-extraction and
bitterness will result. Too fine a grind may also
clog the filter. If grind is too coarse, the water
will pass through too quickly and the desired
flavors will not be extracted. The Fully Automatic
Burr Grind & Brew™ Thermal Coffeemaker is
preset for a medium grind, the optimal grind for
this type of coffeemaker.
PERFECT CUP OF COFFEE
It is generally agreed that there are four basic
elements critical to the perfect cup of coffee:
Element 1: Water
Coffee is 98% water. Often overlooked, the
quality of the water is as important as the quality
of the coffee. A good rule of thumb is that if
your water doesn’t taste good from the tap, it
won’t taste any better in your coffee. That’s why
Cuisinart has added a water filter to the Fully
Automatic Burr Grind & Brew™ Thermal
Coffeemaker. The charcoal water filter removes
chlorine, bad tastes and odors, for the purest
cup of coffee every time.
Element 4: Proportion
The Fully Automatic Burr Grind & Brew™
Thermal Coffeemaker makes up to twelve cups
(54 oz.) of coffee.
Using Whole Beans
We recommend refilling the hopper after two full
pots of coffee have been brewed. Be sure that
you have a sufficient amount of beans in your
hopper for the amount of coffee you intend to
brew.
Element 2: Coffee
While the bulk of the liquid is water, all of the
flavor should be from the coffee. To achieve the
same great quality cup of coffee you receive at
a coffee bar, you need to use the same quality
beans. Buy the beans fresh and whole, only
about two weeks’ supply at a time for maximum
freshness. Once the coffee bean is broken, its
flavor degrades very quickly. That’s why the
Fully Automatic Burr Grind & Brew™ Thermal
Coffeemaker grinds your coffee just prior to
brewing. If it is not practical to buy small
supplies, we recommend you separate larger
amounts of beans into one to two week portions
immediately after purchase, and freeze them in
airtight containers. The best way to maximize
freshness is to minimize exposure to air, light
and moisture. So, once beans have been
removed from the freezer, maintain them in a
sealed container at room temperature, since
damaging condensation occurs every time the
beans are removed from the freezer or
NOTE: The maximum capacity for whole beans
is ½ lb. — enough for over two 12-cup pots of
coffee.
Using Pre-Ground Coffee
Although it is preferable to use fresh, whole
beans, you can make coffee in the Fully
Automatic Burr Grind & Brew™ Thermal
Coffeemaker using pre-ground beans. To do so,
turn off the grinder by pressing the Grind Off
button before turning on the unit.
Our recipe
We suggest that you use 1 level scoop of
ground coffee per cup. Adjust the amount to
your taste.
refrigerator. Note that some coffee experts
advise against freezing dark-roast beans,
because freezing can cause the oils to
coagulate. Other experts disagree. We suggest
you experiment and decide for yourself.
NOTE: The maximum capacity for ground coffee
is 16 level scoops, using either a paper or
permanent filter. Exceeding this amount may
cause overflow.
ꢃ
7. Brew Pause™
FeATureS And
BeneFITS
Stops flow of coffee from basket when
carafe is removed from resting plate, so a
cup can be poured in mid-brew, if desired.
Do not remove carafe for longer than 20
seconds.
1. Hopper Container Release Knob
Locks hopper container onto the unit.
8. Thermal Carafe with Hands-Free Lid
An easy pour, no drip double-wall insulated
12-cup stainless steel thermal carafe with
ergonomic handle.
2. Hopper Container
Can be taken out from the unit, for easy
filling and/or cleaning. A safety interlock
system prevents operation of the unit if the
hopper container is removed.
Coffee brews through and pours through a
unique lid that seals air out to provide fresh
flavor. No need to turn or adjust lid.
3. Hopper Container Lid
Keeps beans fresh by sealing out harmful
light, moisture and air.
9. Resting Plate
Scratch-resistant with nonstick coating.
4. Water Reservoir
(not shown) with
Water Level Window
5. Showerhead (not shown)
Distributes water
1
2
evenly over coffee.
6. Control Panel
(see detailed drawing
on page 8)
3
Contains:
On/Off Switch
Hour Set/Minute Set
Clock Display
Program Setting
Grind Off
Grind Control
Strength Control
4
7
8
9
ꢄ
11
12
13
14a 14b14c
10. Cord Storage (not shown)
11. Water Reservoir Cover
Flips back for easy filling.
12. Charcoal Water Filter (not shown) and
Holder (see page 9 for actual filter)
Charcoal water filter eliminates chlorine,
bad tastes and odors from tap water.
13. Burr Grinder
14. Coffee Channel Assembly
a. Channel Cover
Flips back, for cleaning of coffee chute.
NOTE: Cover must be in place before
grinding.
b. Coffee Chute
c. Grind Chute Lever
For easy cleaning.
15
15. Filter Basket Door Release Button
16. Filter Basket Door
A safety interlock system prevents
operation of the unit if the filter basket door
is not closed prior to brewing. (You will hear
a click when the door is properly shut.)
17
17. Filter Basket Cover
Before grinding match GRIND arrows.
To remove, lift where “LIFT” indicates.
NOTE: Cover becomes hot after coffee is
brewed. Use caution when removing cover.
A safety interlock system prevents
operation of the unit if the filter basket
cover is not in place.
18
18. Gold Tone Cuisinart Commercial
Style Filter
A note about filters: When using our
permanent filter, be sure that the handle is
positioned toward the front of the unit. If
you do not, the handle may interfere with
the flow of coffee into the filter basket.
Also note: using our permanent gold-tone
filter will allow some fine coffee grounds to
fall into the coffee carafe. This will appear
as sediment in the carafe.
16
19
19. Filter Basket
Holds our commercial style permanent filter
or #4 paper filter. Removable for easy
cleaning.
A safety interlock system prevents
operation of the unit if the filter basket door
is not closed prior to brewing.
ꢅ
mode and can operate either button to select
the desired time. The buttons can be held down
to scroll through the digits, or pressed and
released to advance one digit at a time. When
scrolling, the numbers will advance slowly at
first and then speed up to the rate of about
three per second. When the number displayed
approaches the desired time, release the button
and press repeatedly to advance one digit at a
time. Be careful to make sure that the PM
indicator is on if a PM time is desired.
CONTROL PANEL
1. On/Off button with LED Indicator
Audible Tone (not shown): The Fully
Automatic Burr Grind & Brew™ Thermal
Coffeemaker is equipped with an audible
tone which will sound 5 times when the
coffee has completed brewing (coffee may
continue to stream from the filter for several
seconds afterward). Unit will automatically
shut off.
2. Hour and Minute Buttons
Exiting Time Set Mode
Press and hold either Hour or Min for
approximately 2 seconds to enter Time Set
Mode.
The Time Set mode can be exited in one of two
ways:
1. Press any button besides the Hour or
Minute button. This will exit the Time Set
mode and activate the selected function.
3. Clock/LCD Display
Displays time of day and program setting
when Program button is pressed. Displays
Strength Control setting (MILD, MED or
STRONG)
2. Do nothing. If neither the Hour or Minute
button is pressed for a period of five
seconds, the Time Set mode will be exited.
4. Program Button with LED Indicator
Setting the Program Time
Press to display or set Auto On time.
When you press the Program Set button, it
displays the current auto on time (default time
12:00 pm).
5. Grind Off Button with LED Indicator
Use to turn off the grinder when using
pre-ground coffee.
Entering Set Program Time Mode
6. Grind Control Knob
Turn the Grind Control to choose the
desired amount of coffee beans to grind.
Press and hold the Program Set button (about 2
seconds) until the green light and LCD display
begin to flash. This signals that you have
entered the Set Program Time mode. The
desired time can be set by pressing the Hour
and Minute buttons to scroll forward through the
digits. Pressing and holding either button will
allow you to scroll continuously, slowly at first,
and then to accelerate to the rate of about three
digits per second. As the desired time setting
approaches, release the button and press
repeatedly to advance one digit at a time.
The coffeemaker will start to brew at the pro-
grammed time. The Program mode cannot be
entered if the coffeemaker is in its brew cycle.
7. Strength Control Button
Press to choose coffee strength: mild,
medium, or strong. Selected coffee
strength will show on Clock Display.
PROGRAMMING YOUR
COFFEEMAKER
Setting the Clock
When the coffeemaker is plugged in, 12:00 will
appear until you set the time.
Entering Time Set Mode
Exiting Set Program Time Mode
Set Program Time may be exited in any of three
ways:
To set the time, hold down either the Hour or
Minute button until the clock begins flashing
(about 2 seconds). You are now in the Time Set
ꢆ
1. Press the Program Set button again. This
will cause the coffeemaker to revert to its
previous state.
all the way down to the base of the unit,
along the reservoir wall.
NOTE: We recommend changing the water filter
every 60 days or 60 uses or more often if you
have hard water.
2. Press any other button (except Hour or
Minute). Set Program Time mode will be
exited and the function of the button
pressed will be executed.
Replacement water filters can be purchased in
stores or by calling customer service or through
the Cuisinart website.
3. Do nothing. If neither the Hour nor Minute
button is pressed for a period of five
seconds, the Set Program Time mode will
be exited and the programmed setting will
be in effect.
MAKING COFFEE WITH
WHOLE BEANS
Before you make the first pot of coffee in your
new Cuisinart® Fully Automatic Burr Grind &
Brew™ Thermal Coffeemaker, we recommend
operating the coffeemaker once, using only
water and a paper filter. This will remove any
dust or residues which will remain in the system
from the manufacturing process. Note: Allow the
grinder to grind free of beans for this process.
INSERTING THE WATER
FILTER
1. Fill the Water Reservoir
Open the reservoir lid. Pour the desired
amount of water in the reservoir using the
water level window indicator. Close the
reservoir lid. Note: Do not exceed the
12-cup line. Doing so may cause the carafe
to overflow.
2. Add Beans
Lift the hopper lid, using the recess on
either side. Fill the hopper with beans. We
recommend keeping the hopper at least
halfway full. Be sure that you have a
sufficient amount of beans in your hopper
for the amount of coffee you intend to brew
(maximum capacity is ½ lb. Do not over-
pack the hopper. Over-packing may result
in jamming the grinder.)
a. Remove the filter from polybag and soak in
cold tap water for 15 minutes.
b. Remove the water filter holder from the
coffeemaker by lifting it out of the reservoir
area with your thumb and forefinger.
c. Grasp the stem in one hand. Using the
thumb of the other hand, gently press
down and pull toward you. Compartment
will flip open.
For easy filling, the hopper container can be
taken out by turning the hopper container
release knob to the unlock position.
Note: Do not put any water in the unit once the
hopper container has been removed. If water
gets into the grinder motor, the motor may
become damaged and may malfunction.
d. Place the filter in the holder and close the
water filter holder; you will hear a snap
indicating filter is in place.
NOTE: Caution must be used when inserting the
charcoal filter. Improper placement in the holder
can cause tearing of the filter skin.
Put hopper lid back in place.
3. Lock Hopper
If you have removed the hopper from the
unit, be sure that the hopper container
release knob is in the unlocked position and
place the hopper container back in the unit.
e. Hold the filter under cold running tap water
for 10 seconds to flush. You should place
the hole openings in the side of the unit
directly under the water stream.
Turn the knob to locked position.
f. Allow the filter to drain completely.
This unit is equipped with a safety interlock
system. The unit will not grind if the hopper
container is not in place. If you try to turn
g. Replace the water filter holder in the
reservoir area of the coffeemaker, pushing it
ꢇ
on the unit for grinding with the hopper out
of place, the unit will beep continuously
until the missing part is installed.
2. Press the Strength Control button to set
coffee strength. MILD, MED or STRONG
will show on the LCD display.
The brewing process can be restarted by
pressing the On button. Restarting the
process will not affect coffee results.
3. Press the On button. The indicator will light
and the process will begin.
B. Programmed Brewing
4. Insert Coffee Filter
Press the Program button. The indicator
will light and the display will show the
programmed time for as long as the button
is depressed. The display reverts back to
time of day once the button is released.
(To set the programmed time, see
Open filter door by pressing filter basket
door release button. Remove filter basket
cover and place a #4 basket paper filter or
Cuisinart’s commercial style permanent
filter in the basket.
Programming Your Coffeemaker on page 8.)
Note: When using our permanent filter, be sure
that the handle is positioned toward the front of
the unit. If you do not, the handle may interfere
with the flow of coffee into the filter basket.
1. Turn the Grind Control knob to set the
number of cups you want to brew. The
coffeemaker will grind the corresponding
amount of beans. The unit will automatically
adjust for low cup settings.
Also note: Using our permanent gold-tone filter
will allow some fine coffee grounds to fall into
the carafe.
2. Press the Strength Control button to set
coffee strength. MILD, MED or STRONG
will show on the LCD display.
When using a paper filter, be sure that the filter
is completely open while touching the side walls
and bottom of the basket.
3.The coffeemaker will begin brewing at the
programmed time.
Put filter basket cover in place. Close filter door.
(You will hear a click if the door is properly shut.)
6. During and After Brewing
The Brew Pause™ feature allows you to
remove the carafe from the resting plate
during mid-brew. The brewing process
does not stop during this period; only the
flow of coffee from the basket stops. Do
not remove the carafe for longer than 20
seconds or the coffee may overflow the
basket. While we offer this feature, we do
not recommend that you pour coffee before
the cycle has reached completion, since
the coffee brewed at the beginning of the
cycle has a flavor profile which is very
different from the coffee made at the end of
the cycle. Removing a cup during the
brewing cycle will alter the flavor of the
finished pot.
The unit is equipped with a safety interlock
system. The unit will not operate if the filter
basket cover or filter basket are not in place or if
the filter door is not closed. If you try to turn the
unit on while the filter compartment is out of
place, the unit will beep continuously until the
missing part(s) are installed.
Before Brewing Coffee
Remove thermal carafe lid by turning in the
direction of the “unlock” arrow. Prewarm carafe
by rinsing it out with hot water. PREWARMING
THE CARAFE WILL HELP KEEP THE COFFEE
HOTTER.
Return the carafe lid to the carafe. To lock the
lid, turn in the direction of the lock arrow until it
fits tightly on carafe and arrow lines up in the
center of the pour spout. This ensures that the
lid is closed and in the proper position for
brewing and pouring.
When the brewing cycle is completed, five
beeps will sound. Coffee will continue to
stream from the filter for several seconds.
After brewing, the unit will automatically
shut itself off. The thermal carafe will keep
the coffee hot for hours.
Make sure you have replaced the thermal carafe
in it’s position on the resting plate and closed
the top cover.
Bottom of thermal carafe is hot to
touch for several minutes after brewing.
Use caution.
5. Brewing
A. Immediate Grinding and Brewing
1. Turn the Grind Control Knob to set the
number of cups you want to brew. The
coffeemaker will grind the corresponding
amount of beans. The unit will automatically
adjust for low cup settings.
10
MAKING COFFEE WITH
PRE-GROUND BEANS
CLEANING AND
MAINTENANCE
Before you make the first pot of coffee in your
new Cuisinart® Fully Automatic Burr Grind &
Brew™ Thermal Coffeemaker, we recommend
operating the coffeemaker once, using only
water and a paper filter. This will remove any
dust or residues that remain in the system from
the manufacturing process.
COMPLETELY CLEAN AND DRY ALL PARTS
AFTER EVERY USE.
Always turn coffeemaker off and remove the
plug from the electrical outlet before cleaning.
After every use, open filter basket door by
pressing filter basket door release button.
Remove filter basket cover, filter basket and
gold tone filter or paper filter. Discard ground
coffee and paper filter.
1. Fill the Water Reservoir
Open the reservoir lid. Pour the desired
amount of water in the reservoir using the
water level window indicator. Close the
reservoir lid. Note: Do not exceed the 12-
cup line. Doing so may cause the carafe to
overflow.
The filter, filter basket and filter basket cover can
be washed in warm soapy water and rinsed
thoroughly, or cleaned in the upper rack of the
dishwasher. Dry all parts after every use.
Remove the carafe from the heating plate.
Discard any remaining coffee. The carafe and lid
can be washed in warm soapy water and rinsed
thoroughly.
2. Add Coffee Grounds
a. Open filter door. Add ground coffee to
our permanent or #4 paper filter. Our
recipe suggestion: Use 1 level scoop of
ground coffee per cup. Adjust the
amount according to your individual
taste.
We suggest cleaning the hopper and coffee
chute every 1-2 weeks depending on frequency
of use.
b. Place filter basket lid in place. Close filter
door.
To clean the hopper, remove hopper container
and lid by turning the hopper container release
knob to the unlocked position. Discard any
leftover coffee beans.
NOTE: The maximum capacity for ground coffee
is 16 level scoops, using either a paper or
permanent filter. Exceeding that amount may
cause overflow if the coffee is too finely ground.
The hopper container and hopper container lid
can be washed in warm soapy water and rinsed
thoroughly, or cleaned in the upper rack of the
dishwasher. Dry all parts after every use.
3. Brewing
A. Immediate Grinding and Brewing
NOTE: Do not put any water in the unit once the
hopper container has been removed. If water
gets into the grinder motor, the motor may
become damaged and may malfunction.
1. Press the Grind Off button. When this
function is activated, an amber LED will
be illuminated.
2. Press the On button. The indicator will
light and the process will begin.
Wipe the area under the hopper container with
a damp cloth.
B. Programmed Brewing
The coffee channel cover can be flipped back
for easy cleaning of the coffee chute. Push the
coffee channel cover tab away from you and lift
up. Use the brush to remove any ground coffee
that remains. Brush grounds toward you (when
facing the unit head-on) and pull the grind chute
lever toward you to send grounds through the
chute. Be sure the filter basket is in place to
catch the grounds.
Press the Program button. The indicator will
light and the display will show the
programmed time for as long as the button
is depressed. The display reverts back to
time of day once the button is released. (To
set the programmed time, see
Programming Your Coffeemaker on page 8.)
1. Press the Grind Off button. When this
function is activated, an amber LED will
be illuminated.
NOTE: Failing to properly clean the coffee chute
may lead to grind accumulations which can
result in weak-tasting coffee.
2. The coffeemaker will begin brewing at
the programmed time.
Do not use scouring agents or harsh cleansers
on any part of the coffeemaker.
Never immerse base unit in water or other liquid.
To clean base, simply wipe with a clean, damp
11
cloth and dry before storing. Wipe heating plate
with a clean, damp cloth. Never use rough,
abrasive materials or cleansers to clean the
resting plate. Do not dry the inside of the water
reservoir with a cloth, as lint may remain.
To clean, fill the water reservoir to capacity
with a mixture of 1
of white vinegar and 2⁄
⁄
3
3
water. Press the Grind Off button, and turn
the coffeemaker on by pressing the On button.
One cycle should be sufficient to adequately
clean the coffeemaker. When the cycle is
completed and the five beeps sound, turn
coffeemaker off. Repeat operation, this time
using fresh cold water.
DECALCIFICATION
Decalcification refers to removing the calcium
deposits which form over time on the metal
parts of the coffeemaker.
For best performance from your coffeemaker,
decalcify the base unit from time to time. The
frequency depends upon the hardness of your
tap water and how often you use the
coffeemaker.
TROUBLESHOOTING
proBLem
CAuSe
SoLuTIon
Hopper not locked in place
(when brewing with whole
beans)
• Check to see if the hopper container release knob is in the unlocked
position
• Place the hopper container on the unit
• Turn the knob to the locked position
• Press On/Off or Program again to resume
Filter door not closed
• Check to be sure that all components of the filter compartment are in place
• Close filter door (you will hear a click if the door is properly shut)
• Press On/Off or Program again to resume
Filter basket not in place
• Open filter door by pressing the filter door release button
• Hook filter basket with cover onto door
• Close filter door (you will hear a click if the door is properly shut)
• Press On/Off or Program again to resume
Continuous
beeping
Filter basket cover not in
place
• Open filter door by pressing the filter door release button
• Put on cover, matching “grind” arrows
• Hook filter basket with cover onto door
• Close filter door (you will hear a click if the door is properly shut)
• Press On/Off or Program again to resume
Filter Basket not emptied of
used grinds
• Open filter door by pressing the filter door release button
• Remove filter basket with cover
• Discard used grounds
• Replace filter basket with cover and close door
• Press On/Off or Program again to resume
Coffee chute is clogged
• Remove the hopper from the unit
• Lift coffee channel cover
• Clean out coffee chute
• Replace channel cover and hopper
• Your coffeemaker is now ready to brew again
Coffee is
weaker than
usual
Not enough beans in hopper • Be sure there are enough beans in your hopper for the amount of coffee you
intend to brew
Strength setting is incorrect
• Check your strength setting — displayed on the LCD screen
• To change your strength settings press the strength control button
1ꢀ
manufactured to the strictest specifications and
has been designed for use with the authorized
accessories and replacement parts.
WArrAnTY
This warranty expressly excludes any defects or
damages caused by accessories, replacement
parts, or repair service other than those that have
been authorized by Cuisinart.
LImITed THree-YeAr
WArrAnTY
This warranty does not cover any damage caused
by accident, misuse, shipment or other ordinary
household use.
This warranty is available to consumers only. You
are a consumer if you own a Cuisinart® Fully
Automatic Burr Grind & Brew™ Thermal
Coffeemaker that was purchased at retail for
personal, family or household use. Except as
otherwise required under applicable law, this
warranty is not available to retailers or other
commercial purchasers or owners.
This warranty excludes all incidental or
consequential damages. Some states do not allow
the exclusion or limitation of these damages, so
they may not apply to you.
CALIFORNIA RESIDENTS ONLY:
We warrant that your Cuisinart® Fully Automatic
Burr Grind & Brew™ Thermal Coffeemaker will be
free of defects in materials and workmanship under
normal home use for 3 years from the date of
original purchase.
California law provides that for In-Warranty Service,
California residents have the option of returning a
nonconforming product (A) to the store where it
was purchased or (B) to another retail store which
sells Cuisinart products of the same type.
We suggest you complete and return the enclosed
product registration card promptly to facilitate
verification of the date of original purchase.
However, return of the product registration card
does not eliminate the need for the consumer to
maintain the original proof of purchase in order to
obtain the warranty benefits. In the event that you
do not have proof of purchase date, the purchase
date for purposes of this warranty will be the date
of manufacture.
If your Cuisinart® Fully Automatic Burr Grind &
Brew™ Thermal Coffeemaker should prove to be
defective within the warranty period, we will repair
it, or if we think necessary, replace it. To obtain
warranty service, simply call our toll-free number 1-
800-726-0190 for additional information from our
Customer Service Representatives, or send the
defective product to Customer Service at Cuisinart,
150 Milford Road, East Windsor, NJ 08520.
The retail store shall then, at its discretion, either
repair the product, refer the consumer to an
independent repair facility, replace the product, or
refund the purchase price less the amount directly
attributable to the consumer’s prior usage of the
product. If the above two options do not result in
the appropriate relief to the consumer, the
consumer may then take the product to an
independent repair facility if service or repair can
be economically accomplished. Cuisinart and not
the consumer will be responsible for the
reasonable cost of such service, repair,
replacement, or refund for nonconforming products
under warranty.
California residents may also, according to their
preference, return nonconforming products directly
to Cuisinart for repair, or if necessary, replacement,
by calling our Consumer Service Center toll-free at
1-800-726-0190.
To facilitate the speed and accuracy of your return,
please enclose $10.00 for shipping and handling of
the product.
Cuisinart will be responsible for the cost of the
repair, replacement, and shipping and handling for
such products under warranty.
Please pay by check or money order (California
residents need only supply proof of purchase and
should call 1-800-726-0190 for shipping
instructions).
BEFORE RETURNING YOUR CUISINART
PRODUCT
If you are experiencing problems with your
Cuisinart® product, we suggest that you call our
Cuisinart® Service Center at 1-800-726-0190
before returning the product serviced. If servicing is
needed, a representative can confirm whether the
product is under warranty and direct you to the
nearest service location.
NOTE: For added protection and secure handling
of any Cuisinart® product that is being returned, we
recommend you use a traceable, insured delivery
service. Cuisinart cannot be held responsible for in-
transit damage or for packages that are not
delivered to us. Lost and/or damaged products are
not covered under warranty. Please be sure to
include your return address, daytime phone
number, description of the product defect, product
model number (located on bottom of product),
original date of purchase, and any other
Important: If the nonconforming product is to be
serviced by someone other than Cuisinart’s
Authorized Service Center, please remind the
servicer to call our Consumer Service Center at
1-800-726-0190 to ensure that the problem is
properly diagnosed, the product serviced with
the correct parts, and the product is still under
warranty.
information pertinent to the product’s return.
Your Cuisinart® Fully Automatic Burr Grind &
Brew™ Thermal Coffeemaker has been
1ꢁ
Coffeemakers
Toasters
Blenders
Ice Cream
Makers
Cookware
Food
Processors
Cuisinart offers an extensive assortment of top quality products to make life in the
kitchen easier than ever. Try some of our other countertop appliances and
®
cookware, and Savor the Good Life .
©2007 Cuisinart
Cuisinart® is a registered
trademark of Cuisinart
Any trademarks or service marks of third
parties used herein are the trademarks or
service marks of their respective owners.
150 Milford Road
East Windsor, NJ 08520
Printed in China
07CU26221
IB-7541
|