Elation Professional Work Light ELED TRI64B User Manual

ELED TRI64B  
Introduction  
Unpacking: Thank you for purchasing the ELED TRI64B by Elation  
Professional®. Every ELED TRI64B has been thoroughly tested and has  
been shipped in perfect operating condition. Carefully check the ship-  
ping carton for damage that may have occurred during shipping. If the  
carton appears to be damaged, carefully inspect your fixture for any  
damage and be sure all accessories necessary to operate the unit has  
arrived intact. In the case damage has been found or parts are miss-  
ing, please contact our toll free customer support number for further  
instructions. Do not return this unit to your dealer without first contact-  
ing customer support.  
ELED TRI64B  
Introduction: The Elation Professional® ELED TRI64B is part of a  
continuing pursuit to create high quality intelligent lighting. The ELED  
TRI64B is a DMX intelligent, high powered LED par can. This fixture  
can be used in a stand alone mode or connected in a Master/Slave  
configuration. The unit can also be controlled via DMX controller. This  
wash has four operating modes: Sound Active mode, Auto mode, RGB  
mode, and DMX control mode.  
Customer Support: Elation provides a customer support line, to  
provide set up help and to answer any question should you encounter  
problems during your set up or initial operation. You may also visit us  
tions. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m.  
Pacific Standard Time.  
Voice:  
Fax:  
(323) 582-3322  
(323) 582-3108  
E-mail:  
Warning! To prevent or reduce the risk of electrical shock or fire, do  
not expose this unit to rain or moisture.  
Caution! There are no user serviceable parts inside this unit. Do not  
attempt any repairs yourself, doing so will void your manufactures war-  
ranty. In the unlikely event your unit may require service please contact  
Elation.  
User Instructions  
PLEASE recycle the shipping carton when ever possible.  
©Elation Professional®  
6122 S. Eastern Ave.  
Los Angeles CA. 90040  
1/08  
 
ELED TRI64B  
Set Up  
ELED TRI64B  
Set Up  
Power Supply: Before plugging your unit in, be sure the source volt-  
age in your area matches the required voltage for your Elation ELED  
TRI64B. The Elation ELED TRI64B is available in a 120v and 220v ver-  
sion. Because line voltage may vary from venue to venue, you should be  
sure your unit voltages matches the wall outlet voltage before attempt-  
ing to operate you fixture.  
chained and can not be split.  
Notice: Be sure to follow figures two and three when making your own  
cables. Do not use the ground lug on the XLR connector. Do not con-  
nect the cable’s shield conductor to the ground lug or allow the shield  
conductor to come in contact with the XLR’s outer casing. Grounding  
the shield could cause a short circuit and erratic behavior.  
COMMON  
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-  
tocol used as a form of communication between intelligent fixtures  
and controllers. A DMX controller sends DMX data instructions from  
the controller to the fixture. DMX data is sent as serial data that trav-  
els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-  
minals located on all DMX fixtures (most controllers only have a DATA  
“OUT” terminal).  
1
2
1
2
DMX +  
DMX -  
DMX512 OUT  
3-PIN XLR  
DMX512 IN  
3-PIN XLR  
3
3
Figure 2  
XLR Female Socket  
XLR Male Socket  
XLR Pin Configuration  
Pin 1 = Ground  
1 Ground  
2 Cold  
2 Cold  
1 Ground  
Pin 2 = Data Compliment (negative)  
3 Hot  
3 Hot  
Pin 3 = Data True (positive)  
DMX Linking: DMX is a language allowing all makes and models of  
different manufactures to be linked together and operate from a single  
controller, as long as all fixtures and the controller are DMX compli-  
ant. To ensure proper DMX data transmission, when using several  
DMX fixtures try to use the shortest cable path possible. The order  
in which fixtures are connected in a DMX line does not influence the  
DMX addressing. For example; a fixture assigned a DMX address of 1  
may be placed anywhere in a DMX line, at the beginning, at the end,  
or anywhere in the middle. When a fixture is assigned a DMX address  
of 1, the DMX controller knows to send DATA assigned to address 1  
to that unit, no matter where it is located in the DMX chain.  
Figure 3  
Special Note: Line Termination. When longer runs of cable are  
used, you may need to use a terminator on the last unit to avoid erratic  
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-  
nected between pins 2 and 3 of a male XLR connector (DATA + and  
DATA -). This unit is inserted in the female XLR connector of the last  
unit in your daisy chain to terminate the line. Using a cable terminator  
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic  
behavior.  
Termination reduces signal errors and  
1
avoids signal transmission problems  
3
and interference. It is always advisable  
2
to connect a DMX terminal, (Resistance  
120 Ohm 1/4 W) between PIN 2 (DMX-)  
Data Cable (DMX Cable) Requirements (For DMX Operation):  
The ELED TRI64B can be controlled via DMX-512 protocol. The ELED  
TRI64B has 6 DMX modes, please see pages 10-  
12 for the different modes. The DMX address is  
set on the back panel of the ELED TRI64B. Your  
unit and your DMX controller require a standard 3-  
pin XLR connector for data input and data output  
(Figure 1). If you are making your own cables,  
be sure to use standard two conductor shielded  
cable (This cable may be purchased at almost all  
pro sound and lighting stores). Your cables should  
and PIN 3 (DMX +) of the last fixture.  
Figure 4  
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR  
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures  
may be implemented in a 3-pin XLR DMX line. When inserting stan-  
dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be  
used, these adaptors are readily available at most electric stores. The  
chart below details a proper cable conversion.  
3-Pin XLR to 5-Pin XLR Conversion  
Conductor  
Ground/Shield  
3-Pin XLR Female (Out)  
5-Pin XLR Male (In)  
Pin 1  
Pin 1  
Pin 2  
Pin 3  
Data Compliment (- signal)  
Data True (+ signal)  
Not Used  
Pin 2  
Figure 1  
Pin 3  
be made with a male and female XLR connector  
Do Not Use  
Do Not Use  
on either end of the cable. Also remember that DMX cable must be daisy  
Not Used  
 
ELED TRI64B  
Operating Instructions  
ELED TRI64B  
Operating Instructions  
follow the “Master.”  
LED Display On/Off:  
To set the LED display to turn off after 10 seconds, press the MODE  
button until 0001 is displayed, press the UP button to display 0002.  
Now the display will disappear after 10s. Press any button to turn  
the display on again. Be advised though that the display will turn off  
automatically after 10 seconds.  
Sound Active Mode:  
In this mode the ELED TRI64B will react to sound, and chase through the  
different colors.  
1. Plug the fixture in and press the MODE button until “7-So” is dis-  
played.  
To set the display press the MODE button until 0001 is displayed. The  
display will now stay on at all times.  
0001= LCD display on at all times.  
2. The fixture will now change via sound.  
Macro Mode:  
1. Plug the fixture in and press the MODE button until “8-XX” is dis-  
played.  
0002= LCD display shuts off after 10 seconds.  
Operating Modes:  
You can use the ELED TRI64B in four ways:  
2. There are 35 macros to choose from. Select your desired macro by  
pressing the UP and DOWN buttons.  
• Sound-Active mode - The unit will react to sound, chasing through the  
built in programs.  
Auto Mode:  
1. Plug the fixture in and press the MODE button until “9-XX” is dis-  
played.  
• Macro Mode - There are 35 color macros to choose from.  
• Auto Mode - There are 6 built in programs to choose from.  
• DMX control mode - This function will allow you to control each  
individual fixtures traits with a standard DMX 512 controller such as  
as the Elation® Show Designer™.  
2. There are 6 built in programs to choose from. Select your desired  
program by pressing the UP and DOWN buttons. You can set your  
program speed by following the instructions below.  
Master-Slave Operation:  
Auto Mode Speed Adjustment:  
This function will allows you to link units together to run in a Master-  
Slave mode. In Master-Slave operation one unit will act as the controlling  
unit and the others will react to the controlling units built-in programs.  
Any unit can act as a Master or as a Slave however, only one unit can be  
programmed to act as the “Master.”  
1. To adjust the speed of your Auto mode program press the MODE  
button until “A-XX” is displayed.  
2. Press the UP or DOWN buttons to make the adjustmetns. “A-01” is  
the slowest speed, “A-15” the fastest speed. When the display  
reads “A-00” the Auto mode is running by sound activity. Set to your  
desire.  
Master-Slave Connections and Settings:  
1. Daisy chain your units via the XLR connector on the rear of the unit.  
Use standard XLR microphone cables to link your units together.  
Remember that the Male XLR connector is the input and the Female  
XLR connector is the ouput. The first unit in the chain (master) will  
use the female XLR connector only. The last unit in the chain will use  
the male XLR connector only.  
2. Set the “Master” unit to your desired mode or operation.  
3. For the “Slave” unit(s), set the display to DMX mode 3, or 3 Channel  
mode. The display should read “3000” or any variables, i.e “3001”,  
“3002 etc..  
DMX Mode:  
Operating through a DMX controller gives the user the freedom to create  
their own programs tailored to their own individual needs. This function  
also allows you to use your fixtures as spot lights. The ELED TRI64B has  
6 DMX modes: 1 Channel mode, 2 Channel mode, 3 Channel mode, 4  
Channel mode, 6 Channel mode, and a 7 Channel mode. See pages 10-  
12 for each modes’ DMX traits.  
1. This function will allow you to control each individual fixture’s traits  
with a standard DMX 512 controller such as the Elation® Show  
Designer™ or the Elation® DMX Operator™.  
2. To run your fixture in DMX mode, plug in the fixture via the XLR con-  
4. Connect the “Slave” unit or units and they will automatically start to  
 
ELED TRI64B  
Channel  
1 Channel - DMX Values & Functions  
ELED TRI64B  
Operating Instructions  
nections to any standard DMX controller. Select your desired DMX  
mode, and then press the UP or DOWN buttons to adjust the DMX  
address.  
Value  
0 - 255  
Function  
1
MACROS  
3. To run the 1 Channel Mode, press the MODE button until “1000”  
is displayed. This is the DMX addressing for the 1 Channel Mode.  
4. To run the 2 Channel Mode, press the MODE button until “2000”  
is displayed. This is the DMX addressing for the 2 Channel Mode.  
5. To run the 3 Channel Mode, press the MODE button until “3000”  
is displayed. This is the DMX addressing for the 3 Channel Mode.  
6. To run the 4 Channel Mode, press the MODE button until “4000”  
is displayed. This is the DMX addressing for the 4 Channel Mode.  
7. To run the 6 Channel Mode, press the MODE button until “5000”  
is displayed. This is the DMX addressing for the 6 Channel Mode.  
8. To run the 7 Channel Mode, press the MODE button until “6000”  
is displayed. This is the DMX addressing for the 7 Channel Mode.  
9. Please see pages 10-12 for DMX values and traits.  
ELED TRI64B  
Channel  
2 Channel - DMX Values & Functions  
Value  
0 - 255  
0 - 255  
Function  
1
2
MACROS  
DIMMER 0% - 100%  
ELED TRI64B  
Channel  
3 Channel - DMX Values & Functions  
Value  
0 - 255  
Function  
1
2
3
RED  
0%  
GREEN  
0% 100%  
BLUE  
100%  
100%  
0 - 255  
0 - 255  
0%  
ELED TRI64B  
Channel  
4 Channel - DMX Values & Functions  
Value  
0 - 255  
Function  
1
RED  
0%  
GREEN  
0% 100%  
BLUE  
100%  
DIMMING  
0% 100%  
100%  
2
0 - 255  
3
0 - 255  
0%  
4
0 - 255  
 
ELED TRI64B  
Channel  
6 Channel - DMX Values & Functions  
ELED TRI64B  
7 Channel - DMX Values & Functions  
Value  
0 - 255  
Function  
Channel  
Value  
Function  
1
2
3
RED  
1
0 - 255  
0 - 255  
0 - 255  
RED  
0%  
GREEN  
0% 100%  
BLUE  
0% 100%  
100%  
0%  
GREEN  
0% 100%  
BLUE  
100%  
100%  
0 - 255  
2
0 - 255  
3
0%  
4
5
16 - 255  
COLOR MACRO  
4
5
16 - 255  
COLOR MACRO  
0 - 15  
NOTHING  
0 - 15  
NOTHING  
16 - 255  
STROBING  
16 - 255  
STROBING/SPEED CONTROL  
6
0 - 255  
DIMMING  
6
MODE  
0%  
100%  
0 - 31  
32 - 63  
64 - 95  
96 - 127  
128 - 159  
160 - 191  
192 - 223  
224 - 255  
RGB USING CHANNEL’S 1, 2, & 3  
DIM  
BRIGHT  
BRIGHT  
DIM  
Channel 1, 2, and 3 will not work, when Channel 4 is being  
used.  
DIM  
BRIGHT  
DIM  
When using Channel 4, Channel 5 will control the speed of the  
macro.  
COLOR MIXING  
3 COLOR CHANGE  
7 COLOR CHANGE  
SOUND ACTIVE  
7
0 - 255  
DIMMING  
0%  
100%  
Channel 1, 2, and 3 will not work, when Channel 4 is being  
used.  
When using Channel 6, Channel 5 will control the speed of the  
color changing.  
 
ELED TRI64B  
Fuse Replacement  
ELED TRI64B  
Warranty  
2-YEAR LIMITED WARRANTY  
Locate and remove the unit’s power cord. Once the cord has been  
removed located the fuse holder located inside the power socket.  
Insert a flat-head screw driver into the power socket and gently pry out  
the fuse holder. Remove the bad fuse and replace with a new one. The  
fuse holder also has a holder for a spare fuse.  
A. Elation Professionals® hereby warrants, to the original purchaser, Elation Profes-  
sionals® products to be free of manufacturing defects in material and workmanship  
for a period of two years (730 days) from the date of purchase. This warranty shall be  
valid only if the product is purchased within the United States of America, including  
possessions and territories. It is the owner’s responsibility to establish the date and  
place of purchase by acceptable evidence, at the time service is sought.  
ELED TRI64B  
Trouble Shooting  
B. For warranty service, send the product only to the Elation Professionals® factory.  
All shipping charges must be pre-paid. If the requested repairs or service (including  
parts replacement) are within the terms of this warranty, Elation Professionals® will  
pay return shipping charges only to a designated point within the United States. If the  
entire instrument is sent, it must be shipped in its original package. No accessories  
should be shipped with the product. If any accessories are shipped with the product,  
Elation Professionals® shall have no liability whatsoever for loss of or damage to any  
such accessories, nor for the safe return thereof.  
Listed below are a few common problems the user may encounter,  
with solutions.  
Unit not responding to DMX:  
1. Check that the DMX cables are connected properly and are  
wired correctly (pin 3 is “hot”; on some other DMX devices  
pin 2 may be ‘hot’). Also, check that all cables are connected  
to the right connectors; it does matter which way the inputs  
and outputs are connected.  
C. This warranty is void if the serial number has been altered or removed; if the prod-  
uct is modified in any manner which Elation Professionals® concludes, after inspec-  
tion, affects the reliability of the product; if the product has been repaired or serviced  
by anyone other than the Elation Professionals® factory unless prior written authori-  
zation was issued to purchaser by Elation Professionals®; if the product is damaged  
because not properly maintained as set forth in the instruction manual.  
Unit does not respond to sound:  
1. Quiet or high pitched sounds will not activate the unit.  
2. Make sure that you are in Sound Active mode.  
D. This is not a service contract, and this warranty does not include maintenance,  
cleaning or periodic check-up. During the period specified above, Elation Profession-  
als® will replace defective parts at its expense, and will absorb all expenses for war-  
ranty service and repair labor by reason of defects in material or workmanship. The  
sole responsibility of Elation Professionals® under this warranty shall be limited to the  
repair of the product, or replacement thereof, including parts, at the sole discretion of  
Elation Professionals®. All products covered by this warranty were manufactured after  
January 1, 1990, and bear identifying marks to that effect.  
ELED TRI64B  
Cleaning  
Due to fog residue, smoke, and dust cleaning the internal and exter-  
nal optical lenses must be carried out periodically to optimize light  
output.  
E. Elation Professionals® reserves the right to make changes in design and/or  
improvements upon its products without any obligation to include these changes in  
any products theretofore manufactured.  
1. Use normal glass cleaner and a soft cloth to wipe down the  
outside casing.  
2. Clean the external optics with glass cleaner and a soft cloth  
every 20 days.  
3. Always be sure to dry all parts completely before plugging  
the unit back in.  
Cleaning frequency depends on the environment in which the fixture  
operates (i.e. smoke, fog residue, dust, dew).  
F. No warranty, whether expressed or implied, is given or made with respect to any  
accessory supplied with products described above. Except to the extent prohibited  
by applicable law, all implied warranties made by Elation Professionals® in connec-  
tion with this product, including warranties of merchantability or fitness, are limited in  
duration to the warranty period set forth above. And no warranties, whether expressed  
or implied, including warranties of merchantability or fitness, shall apply to this prod-  
uct after said period has expired. The consumer’s and or Dealer’s sole remedy shall  
be such repair or replacement as is expressly provided above; and under no circum-  
stances shall Elation Professionals® be liable for any loss or damage, direct or conse-  
quential, arising out of the use of, or inability to use, this product.  
G. This warranty is the only written warranty applicable to Elation Professionals®  
Products and supersedes all prior warranties and written descriptions of warranty  
terms and conditions heretofore published.  
 
ELED TRI64B  
Specifications  
ELED TRI64B™  
Model:  
SPECIFICATIONS:  
LEDs:  
18 1 Watt LED’s ~ 3 LEDs per Lens  
54 Watts Total  
Working Position:  
Voltage:  
Power Draw:  
Fuse:  
Any safe working position  
100V ~ 240V/47~63Hz  
70W  
120V 2 Amp / 230V 1 Amp  
9.0lbs./ 4.1Kgs.  
Weight:  
Dimensions:  
16.8” (L) x 8.74” (W) x 9.7” (H)  
428.6 x 222 x 246.5mm  
RGB Color Mixing  
Colors:  
DMX Channels:  
6 DMX Modes: 1 Channel Mode,  
2 Channel Mode, 3 Channel Mode,  
4 Channel Mode, 6 Channel Mode,  
& 7 Channel Mode  
Warranty:  
2 Year (730 days)  
Please Note: Specifications and improvements in the design of  
this unit and this manual are subject to change without any prior  
written notice.  
©Elation Professionals®  
A Division of the AmericanDJ® Group of Companies  
World Headquarters:  
6122 S. Eastern Ave. Los Angeles, CA 90040 USA  
Tel: 323-582-3322 Fax: 323-582-3311  
 

Code Alarm Automobile Alarm 1000 User Manual
Cornelius Ice Maker CM450 User Manual
Creative Labs Computer Hardware PN 03SB150600000 User Manual
Cuisinart Coffeemaker DTC 800 Series User Manual
Curtis Home Theater System DVD5038 User Manual
Dynacord Stereo Amplifier PM2600 User Manual
Electro Voice Microphone PL78 User Manual
Estate Range TGS325 User Manual
Fundex Games Games Wormy Apples User Manual
Furman Sound Power Supply IT 1210 User Manual