Gefen Network Card EXT HDMI 5BNC User Manual

Over RGB  
EXT-HDMI-5BNC  
User Manual  
 
CONTENTS  
1
2
3
4
5
6
7
8
9
Introduction  
Operation Notes  
Features  
Sender Panel Layout  
Sender Panel Descriptions  
Receiver Panel Layout  
Receiver Panel Descriptions  
Connecting And Operating The HDMI Over RGB  
Specications  
10 Warranty  
 
INTRODUCTION  
Congratulations on your purchase of the HDMI Over RGB. Your complete  
satisfaction is very important to us.  
Gefen  
Gefen delivers innovative, progressive computer and electronics add-on solutions  
that harness integration, extension, distribution and conversion technologies.  
Gefen’s reliable, plug-and-play products supplement cross-platform computer  
systems, professional audio/video environments and HDTV systems of all sizes  
with hard-working solutions that are easy to implement and simple to operate.  
The Gefen HDMI Over RGB  
The Gefen HDMI over RGB Extender is a handy dongle extension solution  
which takes an HDMI signal and extends it far away over legacy 4- or  
5-connector coaxial cabling. The HDMI over RGB Extender employes Gennum’s  
ActiveConnect technology and is capable of delivering 1080p HDMI at distances  
up to 330 feet (100 meters).  
This is the ideal system for existing installations that are using RGBHV wiring  
and would like to step up to a digital signal but not rip into the walls to rewire the  
installation.  
How It Works  
Simply connect one end of the supplied HDMI cable to your HDMI video source.  
Connect the other end of the supplied HDMI cable to the input side of the HDMI  
over RGB Sender unit. Connect the HDMI over RGB Sender to the sending end  
of your 4- or 5-plug coaxial cable run. If you are using a 5 cable conguration,  
power will be supplied to the receiving unit. If you have a 4-cable conguration, a  
second 5V power supply (sold separately) needs to be connected to the receiver  
unit. At the receiving end of your coaxial cable extension, plug your HDMI over  
RGB Receiver unit into your coaxial cable endpoints, then plug the HDMI over  
RGB Receiver into your HDMI display. You will now see HDMI audio/video at  
the remote location with perfect clarity and sound. You can connect and place  
an optional Gefen IR Emitter/Blaster on the IR receiver of equipment you wish to  
control from the remote location.  
Note: This HDMI product supports BOTH Audio and Video signals.  
1
 
OPERATION NOTES  
READ THESE NOTES BEFORE INSTALLING OR  
OPERATING THE HDMI OVER RGB  
The HDMI Over RGB is designed for either 4 or 5 BNC cable type setups.  
When 5 BNC cables are present and used, a power supply on the HDMI  
Over RGB Receiver will not need to be used. Power will be transmitted over  
the cables. When a 4 BNC cable setup is used, a second power supply  
(part# EXT-PS52AU) for the receiving unit will need to be purchased and  
connected.  
HDMI 1.3 compliant. Please see page 3 for a listing of supported HDMI 1.3  
features.  
HDCP compliant.  
The HDMI Over RGB has an IR repeater feature that will send standard  
IR remote control commands from the receiver back to the sender. This  
is useful for controlling equipment from a remote location. IR commands  
cannot be relyed from the sender to the receiver. Please see page 8 for  
more details.  
Resolutions of up to 1080p Full HD are supported for HDTV use.  
Resolutions of up to 1920 x 1200 are supported for computer use.  
The HDMI Over RGB was designed for use with 75Ω coaxial cable.  
2
 
FEATURES  
Features  
Connects HDMI sources to remote HDMI displays over legacy RGBHV  
cabling  
Supports extension distances of up to 330 feet  
Supports resolutions up to 1080p, 2K, and 1920 x 1200  
HDMI and HDCP compliant  
Extends any IR device  
HDMI 1.3 Features  
Lip-Sync Pass Through  
340 MHz (up to 16 bit YUV 444 supported @ 1080p)  
Deep Color Supported (XV Color Supported)  
Dolby TrueHD & DTS Master Supported  
CEC Protocol Pass Through  
Package Includes  
(1) HDMI Over RGB Sender  
(1) HDMI Over RGB Receiver  
(1) 6 Foot HDMI Cable (M-M)  
(1) 5V DC Power Supply  
(1) User’s Manual  
3
 
SENDER PANEL LAYOUT  
Front Panel  
1
2
3
4
Back Panel  
5
6
7
8
9
4
 
SENDER PANEL DESCRIPTIONS  
1
2
Locking 5V DC Power Supply Input  
Connect the included 5V DC power supply to this input port.  
HDMI Input Port  
Connect the HDMI source device to this input port. A secure connection to this  
HDMI port can be made using Gefen MonoLOK cables.  
3
4
IR Out Port  
An IR emitter/blaster (sold separately, part# EXT-2IREMIT) must be connected  
to this port to use the IR Repeater feature. Connect the emitter to this output port  
and then connect the emitter “eye” on or near the IR receiver of the equipment  
that is intended for control.  
Link LED Indicator  
This LED indicator will become active once a valid link has been established  
between the sending and receiving units. If this LED does not activate there is a  
possible mis-connection between the two units.  
5
6
7
8
9
Red BNC Connector  
This connector will transmit the RED signal data to the receiving unit. The cable  
used for this connection cannot be omitted.  
Green BNC Connector  
This connector will transmit the GREEN signal data to the receiving unit. The  
cable used for this connection cannot be omitted.  
Blue BNC Connector  
This connector will transmit the Blue signal data to the receiving unit. The cable  
used for this connection cannot be omitted.  
Clock BNC Connector  
This connector will transmit the CLOCK signal data to the receiving unit. The  
cable used for this connection cannot be omitted.  
Receiver Power BNC Connector  
This connector will transmit the power needed to operate the receiving unit. The  
cable used for this connection can be omitted when using a 4 BNC type of cable  
setup. If this cable is omitted power must separately be supplied to the receiver  
by one of the included 5V DC power adapters.  
5
 
RECEIVER PANEL LAYOUT  
Front Panel  
1
2
3
4
5
Back Panel  
6
7
8
9
10  
6
 
RECEIVER PANEL DESCRIPTIONS  
1
2
Locking 5V DC Power Supply Input  
When using a 5 BNC cable system this connector will not need to be used.  
When using a 4 BNC cable system a second 5V DC power supply (part# EXT-  
PS52AU) must be purchased and connected to this input port.  
IR Receiver  
This receiver is used for the IR Repeater feature. This receiver will accept  
standard IR remote commands for transmission back to the sending unit and  
then to the connected IR emitter/blaster.  
3
4
HDMI Output Port  
Connect the HDMI capable display device to this output port. A secure  
connection to this HDMI port can be made using Gefen MonoLOK cables.  
IR Extension Port  
An IR receiver extension (sold separately, part# EXT-RMT-EXTIR) can be  
connected to this port to relocate the IR receiver. This option is available so that  
the receiving unit can be placed out-of-sight while still retaining the usability of  
the IR Repeating feature.  
5
Link LED Indicator  
This LED indicator will become active once a valid link has been established  
between the sending and receiving units. If this LED does not activate there is a  
possible mis-connection between the two units.  
6
7
8
9
Red BNC Connector  
This connector will transmit the RED signal data to the receiving unit. The cable  
used for this connection cannot be omitted.  
Green BNC Connector  
This connector will transmit the GREEN signal data to the receiving unit. The  
cable used for this connection cannot be omitted.  
Blue BNC Connector  
This connector will transmit the Blue signal data to the receiving unit. The cable  
used for this connection cannot be omitted.  
Clock BNC Connector  
This connector will transmit the CLOCK signal data to the receiving unit. The  
cable used for this connection cannot be omitted.  
10 Receiver Power BNC Connector  
This connector will transmit the power needed to operate the receiving unit. The  
cable used for this connection can be omitted when using a 4 BNC type of cable  
setup. If this cable is omitted power must separately be supplied to the receiver  
by one of the included 5V DC power adapters.  
7
 
CONNECTING AND OPERATING THE HDMI OVER RGB  
How to Connect the HDMI Over RGB  
1. Connect the HDMI source device to the HDMI Over RGB sender unit using  
the supplied HDMI cable.  
2. The HDMI Over RGB sender and receiver can be used with either a user  
supplied 4 or 5 BNC cable system.  
5 BNC Cables  
Connect all 5 BNC cables to the R, G, B, C, and RP BNC connectors  
between the HDMI Over RGB sender and receiver units.  
4 BNC Cables  
Connect the 4 BNC cables to the R, G, B, and C BNC connectors between  
the HDMI Over RGB sender and receiver units. The RP BNC connector will  
not be used and a second power supply (part# EXT-PS52AU) will need to be  
purchased and connected to the receiver unit.  
3. Connect the HDMI capable display device to the HDMI Over RGB receiver  
unit using a user supplied HDMI cable.  
4. Connect the included 5V DC power adapter to the HDMI Over RGB sender  
unit.  
NOTE: If using a 4 BNC cable system, a second power supply must be  
purchased and connected to the HDMI Over RGB receiver unit.  
5. Power on the display rst and then the source.  
How to Operate the HDMI Over RGB  
The HDMI Over RGB does not require any conguration for standard operation.  
IR Repeater Feature  
An IR emitter/blaster (sold separately, part# EXT-2IREMIT) is required to send  
relayed IR commands to equipment at the sender’s location. Connect the IR  
emitter jack to the HDMI Over RGB sender unit and connect the IR “eye” on  
or near the IR receiver of the equipment that is intended for control. Point the  
equipment’s IR remote at the IR receiver on the HDMI Over RGB receiver unit  
and press buttons to relay commands back to the equipment device.  
8
 
SPECIFICATIONS  
Video Amplier Bandwidth ....................................................................... 340 MHz  
DisplayPort v1.0 compatible ............................................................................. Yes  
Video Resolutions (max) .................................................... 2K, 1080P, 1920x1200  
Power Consumption ....................................................................... 10 Watts (max)  
Coaxial Connectors .......................................................................... 5 x BNC male  
IR back channel ..................................................................................... IR blaster  
HDMI™ Connector ........................................................... Type A (19 Pin) Female  
Input Video Signal .................................................................................... 1.2V p-p  
Input DDC Signal ......................................................................................... 5V p-p  
Power Supply .............................................................................................. 5V DC  
Dimensions ...................................................................... 4.25”W x 1.25”H x 3.9”D  
Shipping Weight ............................................................................................ 4 lbs.  
9
 

Clover Electronics Digital Camera Z670 User Manual
Clover Electronics Security Camera HDC100 User Manual
Cobra Digital Digital Camera DCA1620 User Manual
Concept Enterprises CD Player CD 303 User Manual
Craftsman Pressure Washer 580763 User Manual
Creda Air Conditioner 56040 User Manual
Electro Voice Portable Speaker Force 10 User Manual
Electro Voice Speaker EVX 180B User Manual
Field Controls Oxygen Equipment FDVS User Manual
Gefen Switch Digital Audio Switcher User Manual